Eicon Networks ISDN NT1 Dokumentacja Strona 1

www.eicon.comEiconcard S9x Familyfor PCI-Compatible Bus

10 Making an ISDN ConnectionEiconcard S91 S/T-interface:If your Eiconcard S91 has an S/T-interface, you need a separate NT1. Note You can order an NT

Termination 11TerminationThis section applies to S/T interface users in Australia and North America, and provides instructions to help set up terminat

12 TerminationMultiple ISDN DevicesIf the NT1 is connected to more than one ISDN device, follow the procedures below.75 meters or moreIf the connectio

Making a VHSI Connection 13Making a VHSI ConnectionThe Eiconcard S9x can connect as a DTE to devices such as Data Service Units (DSUs) which support o

14 Interface SpecificationsInterface SpecificationsThe standards compliant with each interface supported on the VHSI port are listed in Table 2. The r

Cable Construction Information 15Cable Construction InformationIf you plan to construct your own VHSI cables, be sure to observe the guidelines given

16 The V.24 DCE InterfaceThe V.24 DCE InterfaceA pin-out diagram for the V.24 DCE interface is shown in Figure 6. The signal definitions and names are

The V.24 DCE Interface 17VHSI—V.24 ConnectionsThe wiring diagram below shows the connections required to construct a VHSI—V.24 DCE cable. For addition

18 The V.24 DTE InterfaceThe V.24 DTE InterfaceA pin-out diagram for the V.24 DTE interface is shown in Figure 8. The signal definitions and names are

The V.24 DTE Interface 19VHSI—V.24 ConnectionsThe wiring diagram below shows the connections required to construct a VHSI—V.24 DTE cable. For addition

www.eicon.comFirst Edition (July 2001) 203-227-01Eicon, Eiconcard, and the Eicon logo are either trademarks or registered trademarks of Eicon Networks

20 The V.35 InterfaceThe V.35 InterfaceA pin-out diagram for the V.35 interface is shown in Figure 10. The signal definitions and names are listed in

The V.35 Interface 21VHSI—V.35 ConnectionsThe wiring diagram below shows the connections required to construct a VHSI—V.35 cable. For additional infor

22 The EIA-530 InterfaceThe EIA-530 InterfaceA pin-out diagram for the EIA-530 interface is shown in Figure 12. The signal definitions and names are l

The EIA-530 Interface 23VHSI—EIA-530 ConnectionsThe wiring diagram below shows the connections required to construct a VHSI—EIA-530 cable. For additio

24 The V.36/RS-449 InterfaceThe V.36/RS-449 Inter-faceA pin-out diagram for the V.36/RS-449 interfaces is shown in Figure 14. The signal definitions a

The V.36/RS-449 Interface 25VHSI—V.36/RS-449 ConnectionsThe wiring diagram below shows the connections required to construct a VHSI—V.36/RS-449 cable.

26 The X.21 InterfaceThe X.21 InterfaceA pin-out diagram for the X.21 interface is shown in Figure 16. The signal definitions and names are listed in

The X.21 Interface 27VHSI—X.21 ConnectionsThe wiring diagram below shows the connections required to construct a VHSI—X.21 cable. For additional infor

28 Back-to-Back ConnectionsBack-to-Back ConnectionsThe wiring diagram below shows the connections required to construct a back-to-back VHSI—VHSI cable

LED Functionality 29LED FunctionalityEiconcard S90, S92, and S94Note The Eiconcard S90 has only one VHSI port.Configuration StatusThis status light il

www.eicon.comTable of ContentsIntroduction ... 5About this Manual...

30 LED FunctionalityEiconcard S91The Eiconcard S91 has three status lights (LEDs) on the end bracket. Two of these lights indicate the status of the I

Technical Specifications 31Technical SpecificationsTechnical Data• PCI bus compatible (32-bit slot)Hardware Installation• Automatic configuration of i

32 Technical SpecificationsVHSI Ports• VHSI ports connect to 36-pin high-density male connectors• Support for V.24, V.35, EIA-530, and V.36/RS-449• X.

International Regulatory Information 33International Regulatory InformationRegulatory Information for the USA:WARNING. Changes or modifications to thi

34 Regulatory Information for the USA:FCC Part 68 NoticeThis unit complies with Part 68 of the FCC rules. On the bottom of this equipment is a label t

Regulatory Information for Canada 35Regulatory Information for CanadaNOTICE: The Industry Canada label identifies certified equipment. This certificat

36 Regulatory Information for EuropeRegulatory Information for Europe EU Declaration of ConformityEN: Eicon Networks Corporation declares that this eq

Regulatory Information for Europe 37Safety Status: SELVNo voltages within this equipment exceed SELV voltages. All interconnection points and ports ar

38 Regulatory information for AustraliaRegulatory information for Australia• This customer equipment shall only be installed in a PC that requires the

www.eicon.com

203-227-01

Introduction 5IntroductionThe S9x family of Eiconcards are PCI Plug-and-Play (PnP) cards that offer X.25 connectivity through one or two (depending on

6 Installing the Eiconcard S9xInstalling the Eiconcard S9xFollow the steps below to install the Eiconcard S9x. If you want the Eiconcard S9x to be ava

Installing the Eiconcard S9x 7Figure 2. Inserting the Eiconcard S9x.e)Fasten the adapter with the screw (to ensure that the adapter is properly secure

8 Making an ISDN ConnectionMaking an ISDN ConnectionNote Only the Eiconcard S91 supports ISDN connections.After you have installed your Eiconcard S91,

Making an ISDN Connection 9Eiconcard S91 U-interface:If your Eiconcard S91 has a U-interface, the NT1 is integrated into the adapter, and you do not n