Eicon Networks S52 Podręcznik Użytkownika Strona 90
- Strona / 91
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
X.3 PAD Parameters
page 88
20:n Echo mask
This parameter specifies the characters from the workstation for which the PAD is to echo
back to the DTE (terminal). The echo mask applies only when parameter 2 (echo) is set to 1.
Coding of parameter 20 can be a single value or the sum of any combination of values listed
above. If parameter 5, 12 or 22 is set to a non-zero value, then X-ON (DC1) and X-OFF (DC3)
are not echoed.
21:n Parity treatment
Not necessary for a software PAD, since an asynchronous signal is not being generated.
Parameter 21 is permanently set to 0 and does not influence parity.
If your application generates parity signals, however, then the PAD will also generate them
and will incorporate them into the packets it transmits. In this case the PAD will also remove
parity signals from incoming packets before sending the data to your application.
22:n Page wait
The workstation will be able to suspend the transmission of additional characters after a
specified number of linefeeds have been received. No further data will be transmitted until
the page wait condition is canceled.
The workstation will cancel the page wait condition and resume normal transmission on receipt
of an X-ON character (Ctrl-Q).
Value Description
0 No Echo mask (all characters echoed)
1 No echo of character CR
2 No echo of character LF
4 No echo of characters VT, HT, FF
8 No echo of characters BEL, BS
16 No echo of characters ESC, ENQ
32 No echo of characters ACK, NAK, STX, SOH, EOT, ETB, ETX
64 No echo of editing characters as designated by parameters 16, 17, and 18
128 No echo of all other ASCII control characters (0-31) not mentioned above,
and the character DEL (ASCII character 127)
Value Description
0 No parity checking or generation
Value Description
0 Page wait disabled
1-255 Page wait condition after n linefeed characters are received by the workstation
- User’s Guide 1
- page 4 4
- Contents 5
- About this Guide 7
- Typographic Conventions 8
- CHAPTER 2 9
- Eiconcard Services 10
- Eiconcard Host PAD Driver 11
- Eiconcard Terminal PAD Driver 11
- Eiconcard Routing Services 12
- Eiconcard SNMP Services 13
- Integrating with OSI 13
- OSI Model 14
- For More Information 15
- page 14 16
- CHAPTER 3 17
- Completing the Installation 18
- Removing Eiconcard Router 18
- Removing Eiconcard Services 19
- Introduction 19
- Install an Eiconcard 19
- Uninstall an Eiconcard 20
- Configure Eiconcard Protocol 20
- High-Level Services 21
- Line Protocols 21
- Dialer Selection 21
- Changing Protocol Parameters 22
- Eiconcard Memory Requirements 22
- Online Help 23
- Configuration Procedure 24
- Configure Advanced Options 25
- Configure the PAD 25
- page 24 26
- Terminal PAD 27
- page 26 28
- Using tpad with cu and uucp 29
- The cu Commands 30
- page 30 32
- X.3 PAD Parameters 33
- The uucp Configuration Files 33
- Using uucp and cu 34
- page 34 36
- CHAPTER 5 37
- page 36 38
- Load the mpr.if file 40
- IP Routing Tables 40
- Displaying IP-routing Entries 42
- Testing Your Installation 42
- The Test System 43
- Resources for the Test System 43
- The Addressing Scheme 43
- Configuring the Eiconcards 44
- Creating an X.25 Test Circuit 45
- Troubleshooting 46
- Setting Up a PPP Connection 48
- page 48 50
- page 50 52
- page 52 54
- CHAPTER 6 55
- Load/Self-test Timeout Period 56
- Watchdog Wake Up Period 56
- X.25 socket driver 56
- Modem and Null-Modem Cables 57
- Establishing Contact 58
- Modem Cables 59
- HSI/V.24 Converter 60
- Null-Modem Cables 61
- X.21 HSI Null-Modem Cable 62
- References 63
- Facility Types 64
- Facility Syntax 64
- Examples of User Facilities 64
- Packet size 65
- Window Size 65
- Fast Select 66
- Throughput Class Negotiation 66
- Bilateral CUG Selection 68
- Reverse Charging 68
- Priority Traffic: 0,0,1,1 69
- Traffic: 69
- 1,1,0,0,1,1 69
- Networks and DNICs 70
- X.25 Diagnostic Codes 71
- page 70 72
- X.25 Cause Codes 73
- ASCII Control Codes 74
- page 74 76
- X.29 Call User Data Format 77
- page 76 78
- Key Packet Formats 79
- Call Accepted Packet Format 80
- Clear Request Packet Format 81
- 2:n Echo 85
- 5:n Auxiliary Device Control 85
- page 84 86
- 8:n Discard data 87
- 9:n Carriage return padding 87
- 10:n Line folding 87
- 11:n Communication speed 87
- 15:n Editing 88
- 14:n Linefeed padding 88
- 16:n Character delete 89
- 17:n Line delete 89
- 18:n Line redisplay 89
- 19:n Editing service signals 89
- 20:n Echo mask 90
- 21:n Parity treatment 90
- 22:n Page wait 90
Powiązane produkty i podręczniki dla Networking Eicon Networks S52
(83 strony)
Networking Eicon Networks C20 Instrukcja Obsługi
(410 strony)
(410 strony)
Networking Eicon Networks C20 Dokumentacja
(24 strony)
(24 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji