Eicon Networks S52 Podręcznik Użytkownika Strona 43
- Strona / 91
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Eicon Connections for Linux User’s Guide
page 41
You may assign your own IP addresses for this test, but it is recommended that you use the
IP addresses suggested in
Resources for the Test System below.
The Test System
The test system described here links two Linux systems together back to back through their
Eiconcards. This procedure also tests the connection backup feature. Although this setup
cannot be considered an internetwork, it tests the Eiconcards’ transmission and reception of
IP datagrams over an X.25, Frame Relay, PPP, or Multilink PPP link.
To simplify the discussion below, the names Sys-1 and Sys-2 are used to identify the two test
systems.
Resources for the Test System
If you performed the installation as described in the Eiconcard Connections for Linux Release
Notes (Readmefirst.txt), you now have a Linux system (Sys-1) made up of the following:
•Hardware
• i386-based or higher Linux system
• An Eiconcard
•Software
•Linux
• Eiconcard Services package
• Eiconcard Routing Services package
A null-modem RS-232 cable or V.35 cable is also required.
To perform the tests, you will need to set up a second system (Sys-2) that is equivalent to
the first. Each system must be uniquely addressed.
Before continuing, make sure that the complete installation procedure has been performed
for Sys-1 and Sys-2.
When both the installations are complete and the systems rebooted, messages referring to
the Eiconcard, the Eiconcard Streams Device Driver (Eiconcard Services package), TCP/IP,
and Eiconcard Routing Services appear in the Linux boot messages.
The Addressing Scheme
Before continuing with the test, you should take a look at the proposed addressing scheme.
Both IP addresses and X.25 DTE addresses (for the X.25 connection) must be considered when
coming up with an addressing scheme for an IP internetwork that uses Eiconcard Routing
Services.
In this simple test the scheme uses an arbitrary assignment of four addresses—two X.25 DTE
addresses (for the X.25 connection), and the two IP addresses. The addresses used in this
test are:
Address Sys-1 Sys-2
X.25 DTE address 3020001 3020123
IP address 192.1.100.1 192.1.100.2
- User’s Guide 1
- page 4 4
- Contents 5
- About this Guide 7
- Typographic Conventions 8
- CHAPTER 2 9
- Eiconcard Services 10
- Eiconcard Host PAD Driver 11
- Eiconcard Terminal PAD Driver 11
- Eiconcard Routing Services 12
- Eiconcard SNMP Services 13
- Integrating with OSI 13
- OSI Model 14
- For More Information 15
- page 14 16
- CHAPTER 3 17
- Completing the Installation 18
- Removing Eiconcard Router 18
- Removing Eiconcard Services 19
- Introduction 19
- Install an Eiconcard 19
- Uninstall an Eiconcard 20
- Configure Eiconcard Protocol 20
- High-Level Services 21
- Line Protocols 21
- Dialer Selection 21
- Changing Protocol Parameters 22
- Eiconcard Memory Requirements 22
- Online Help 23
- Configuration Procedure 24
- Configure Advanced Options 25
- Configure the PAD 25
- page 24 26
- Terminal PAD 27
- page 26 28
- Using tpad with cu and uucp 29
- The cu Commands 30
- page 30 32
- X.3 PAD Parameters 33
- The uucp Configuration Files 33
- Using uucp and cu 34
- page 34 36
- CHAPTER 5 37
- page 36 38
- Load the mpr.if file 40
- IP Routing Tables 40
- Displaying IP-routing Entries 42
- Testing Your Installation 42
- The Test System 43
- Resources for the Test System 43
- The Addressing Scheme 43
- Configuring the Eiconcards 44
- Creating an X.25 Test Circuit 45
- Troubleshooting 46
- Setting Up a PPP Connection 48
- page 48 50
- page 50 52
- page 52 54
- CHAPTER 6 55
- Load/Self-test Timeout Period 56
- Watchdog Wake Up Period 56
- X.25 socket driver 56
- Modem and Null-Modem Cables 57
- Establishing Contact 58
- Modem Cables 59
- HSI/V.24 Converter 60
- Null-Modem Cables 61
- X.21 HSI Null-Modem Cable 62
- References 63
- Facility Types 64
- Facility Syntax 64
- Examples of User Facilities 64
- Packet size 65
- Window Size 65
- Fast Select 66
- Throughput Class Negotiation 66
- Bilateral CUG Selection 68
- Reverse Charging 68
- Priority Traffic: 0,0,1,1 69
- Traffic: 69
- 1,1,0,0,1,1 69
- Networks and DNICs 70
- X.25 Diagnostic Codes 71
- page 70 72
- X.25 Cause Codes 73
- ASCII Control Codes 74
- page 74 76
- X.29 Call User Data Format 77
- page 76 78
- Key Packet Formats 79
- Call Accepted Packet Format 80
- Clear Request Packet Format 81
- 2:n Echo 85
- 5:n Auxiliary Device Control 85
- page 84 86
- 8:n Discard data 87
- 9:n Carriage return padding 87
- 10:n Line folding 87
- 11:n Communication speed 87
- 15:n Editing 88
- 14:n Linefeed padding 88
- 16:n Character delete 89
- 17:n Line delete 89
- 18:n Line redisplay 89
- 19:n Editing service signals 89
- 20:n Echo mask 90
- 21:n Parity treatment 90
- 22:n Page wait 90
Powiązane produkty i podręczniki dla Networking Eicon Networks S52
(83 strony)
Networking Eicon Networks C20 Instrukcja Obsługi
(410 strony)
(410 strony)
Networking Eicon Networks C20 Dokumentacja
(24 strony)
(24 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.079 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji